~ = 261.033MPa

Penstock crater defects finite element analysis


], (2) where (). For the crater at the maximum stress intensity value,ed hardy, it contains little of the various stress components, in fact, that a comprehensive measure of stress levels;. Crater-free defects the local stress values. Stress intensity value to the crater with the vertex distance varies, the relationship between them is shown in Figure 2. Figure 2 Stress intensity and relationship to the crater from the crater of the vertices of the maximum stress intensity value from the crater within a vertex in 6mm,tory burch uk, the stress of rapid change, 6 ~ 14mm range of stress values ​​changed greatly,ed hardy suomessa, 14mm above the stress tends to stable. Single crater when calculating the stress concentration factor: (r plant.) ~ = 261.033MPa, r factory = 166.772MPa, the stress concentration factor calculated from equation f21 k = 1.565. This shows that the crater caused by the strong presence of local stress concentration. More than 2.2 arc calculated in order to analyze more than one pit crater when the stress concentration and the interaction between them, in this study were in girth and longitudinal seam on the existence of two crater as well as in girth and longitudinal seam on the crater of the simultaneous interaction calculation and analysis. Multiple crater finite element model shown in Figure 3. Figure over three crater crater limited Wu model diagram intersection 0 in two welds, longitudinal seam along the arc arranged in a pit, crater 2 arranged along the girth. Two crater along the longitudinal seam and girth arranged in different spacing stress concentration factor are shown in Table 3,abercrombie paris, Table 4. The weld seam and the longitudinal cross-seam in the ring simultaneously on the crater of the stress concentration factor found in Table 5. t-engineering cicadas equal access Zhi Zun Xi Liao: penstock crater defects finite element analysis No. 8 Table 3 arranged along the longitudinal joint when two share in the crater of the stress factor 14253.9761.52330254.18I1.52450261158156680259.9681 .5591213257 .970 I547140256.2l51.536261.6391.569260.569 [. 559259.958l_556257.4521.52326I. 3511.537264.239]. 545 Table 4 arranged along the annular crater when the two stress concentration factor 143050801201402l8034230216223.843223.3l2224.988I_3 07200.481l_253l380201.623]. 3011.342188.3181.2551.339172.8031.26ll349l86.9Rq1. 3oI226943I361190.320t. Stress concentration factor of 321 with a single crater compared to the situation are reduced. This is mainly due to the penstock discontinuity in three directions and the crater group interaction in the local area in the welding of steel. Crater deficit and revenue generated in the arc in the arc crater defects at the same time produce are often prone to crack. As the crater caused by the stress concentration and the role of residual stress near the weld, it is possible at the crater caused by weld cracking. Therefore,ralph lauren danmark, the crater defect must be taken seriously enough. In view of these results. Safety assessment of the strength of the pressure pipe analysis, can only consider the case of a single crater crater at the top of the stress intensity values. 3 Conclusion a. Weld crater defects will cause a strong stress concentration, stress concentration factor of up to 1.565. Therefore, defects of the crater to be taken seriously enough. b. Crater at the stress intensity value and the stress concentration factor of the crater are less sensitive to changes in the distance between. The distribution and location of the crater. G measures the longitudinal seam arranged crater on the stress concentration coefficient crater with quite individual, and in the ring and in the weld seam at the intersection of the longitudinal seam and girth at the same time there Crater, the crater at the stress intensity and stress concentration factors are reduced,ed hardy, therefore, in the strength analysis can only consider the case of a single crater. Table 3, Table 4,abercrombie copenhagen, Table 5 results show that, under various conditions,ed hardy udsalg, References: The crater at the stress intensity and stress concentration coefficient crater of [Jl Zheng Yang - Wan-Lin Guo Fei Click the thickness of a melt bi-material interface notch plate attached to look like,franklin and marshall uk, Zhu (vii) expansion of the main Mino 90 -9 power too 4. Blue Bi metaphor. _ In! Pro master; Qiang 7,franklin marshall outlet,3 ... 199 ... 2 (2): the stress intensity and stress concentration factor and the time of a single crater, ... quite; in the ring and in the weld seam at the intersection of girth and longitudinal [31 Huang Kemin, Jun. Gui Liang, et al. Bias is too take over the head with a three-dimensional seam on the same appear crater, the crater at the stress intensity value and the finite element analysis and strength assessment of pressure vessels. 2003,200) :24-27.

相关的主题文章：


promoting Kaierda service level

respectively

Semi-continuous vacuum brazing furnace automatic c